诚信指数 2
一站通留言 客户留言 联系我们 联系我们 收藏此网站 发送消息
首页
新闻资讯
翻译语种
翻译领域
人才招聘
联系我们
English
search 搜索网站中其它产品:
武汉英语翻译公司
武汉翻译公司
武汉翻译
您现在的位置:武汉市圣士翻译有限责任公司 > 新闻资讯
 
新闻资讯
电脑错误信息中英文对照
发布日期:2011-04-17

电脑错误信息中英文对照

一、BIOS中的提示信息

提示信息     说明   
Drive A error   驱动器A错误   
System halt   系统挂起   
Keyboard controller error   键盘控制器错误   
Keyboard error or no keyboard present   键盘错误或者键盘不存在   
BIOS ROM checksum error BIOS ROM   校验错误   
Single hardisk cable fail   当硬盘使用Cable选项时硬盘安装位置不正确   
FDD Controller Failure BIOS   软盘控制器错误   
HDD Controller Failure BIOS   硬盘控制器错误   
Driver Error   驱动器错误   
Cache Memory Bad, Do not Enable Cache   高速缓存Cache损坏,不能使用   
Error: Unable to control A20 line   错误提示:不能使用A20地址控制线   
Memory write/Read failure   内存读写失败   
Memory allocation error   内存定位错误   
CMOS Battery state Low   CMOS没电了   
Keyboard interface error   键盘接口错误   
Hard disk drive failure   加载硬盘失败   
Hard disk not present   硬盘不存在   
Floppy disk(s) fail (40)   软盘驱动器加载失败,一般是数据线插反,电源线没有插接,CMOS内部软驱设置错误   
CMOS checksum error-efaults loaded.   CMOS校验错误,装入缺省(默认)设置 

二、BIOS刷新失败后,Bootblock启动时出现的提示信息

提示信息                       说明   
Detecting floppy drive A media...   检测软驱A的格式   
Drive media is : 1.44Mb1.2Mb 720Kb 360K   驱动器格式是1.44Mb、12Mb、720kb、360kb的一种  
DISK BOOT FAILURE, INSERT SYSTEM DISK AND PRESS ENTER   磁盘引导失败,插入系统盘后按任意键继续 
三、MBR主引导区提示信息

提示信息         说明   
Invalid partition table   无效的分区表   
Error loading operating sy stem   不能装入引导系统   
Missing operating system   系统引导文件丢失 

  说明:如果在计算机启动过程中,在硬件配置清单下方(也就时在平时正常启动时出现Starting Windows 98…的地方)出现不可识别字符,此时可判断硬盘分区表损坏。如果你的硬盘上有重要资料,这时你不要轻易进行分区,可找专业的数据恢复公司。

四、DOS活动分区中的提示信息

提示信息       说明   
Invalid system disk   无效的系统盘   
Disk I/O error, Replace the disk and press any key.   磁盘I/O错误,替换磁盘后按任意键(当C盘系统文件丢失或被破坏时出现该提示信息。这时可能SYS C:为修复系统文件)   
Invalid Media Type reaching Drive C:   无效的C盘媒体格式说明,也就是C盘没有格式化或者是其他操作系统的磁盘格式如NTFS   
Invalid Boot Diskette Boot Failure   无效的启动盘,启动失败 
五、IO.SYS中的提示信息

提示信息                               说明   
Insert diskette for drive and press any key when ready   插入磁盘到驱动器中后按任意键   
Your program caused a divide overflow error
If the problem persists, contact your program vendor   你的程序导致溢出错误。如果该问题还存在,请联系你的程序供应商   
Windows has disabled direct disk access to protect your long filenames Windows   不能直接访问受保护的长文件名   
The system has been halted. Press Ctrl+Alt+Del to restart your computer   系统挂起,按Ctrl+Alt+Del重新启动你的计算机   
You started your computer with a version of MS-DOS incompatible with this version of Windows. Insert a Startup diskette matching this version of Windows and then restart   你启动的MS-DOS版本与Windows版本不兼容,请插入与Windows版本匹配的系统盘后再重启   
This version of Windows requires a 386 or better processor 该Windows版本需要386以后的CPU支持   
A20 hardware error. Contact technical support to identify the problem   地址线A20错误。联系技术支持来识别该问题   
Starting Windows 98...   正在启动Windows 98……   
Windows 98 is now starting your MS-DOS-based program   Windows 98正在启动基于MS-DOS的程序   
Windows 98 is now restarting...   Windows 98     正在重新启动   
Press Esc now to cancel MS-DOS mode and restart Windows 98...   按Esc退出MS-DOS 模式,重新启动Windows 98…   
There is an unrecognized command in your CONFIG.SYS file   在你的CONFIG.SYS文件中有不可识别的命令   
The following command in your CONFIG.SYS file is incorrect:   在你的CONFIG.SYS有下列错误命令  
The sector size specified in this file is too large:   该文件中指定的扇区太大   
The following file is missing or corrupted: WIN.COM COMMAND.COM   下列文件丢失或被破坏:WIN.COM和COMMAND.COM   
There is an invalid country code or code page in your CONFIG.SYS file   在你的CONFIG.SYS里有一个无效的国家代码   
There is an error in the COUNTRY command in your CONFIG.SYS file   在你的CONFIG.SYS里有一个错误的设置国家命令   
There is not enough memory for the COUNTRY.SYS file   没有足够的内存来加载COUNTRY.SYS文件  
Remove some drivers from your CONFIG.SYS file, and then try again   请从CONFIG.SYS文件中删除部分驱动程序,然后再试   
Remove some drivers, and then try again   去除一些驱动程序,然后再试。这里的驱动程序是指在CONFIG.SYS中使用device或devicehigh命令加载的程序文件   
Remove some disk drivers from your CONFIG.SYS file, and then try again   从你的(CONFIG.SYS)移去部分程序,然后再试   
The configuration specified in your CONFIG.SYS file is too large for memory   调整你的CONFIG.SYS文件以获得足够大的内存   
You have too many block devices specified in your CONFIG.SYS file   调整你的CONFIG.SYS文件以获得block devices   
The STACKS setting(s) in your CONFIG.SYS file are incorrect   在你的CONFIG.SYS中堆栈设置不正确   
 

免责声明:本商铺所展示的信息由企业自行提供,内容的真实性、准确性和合法性由发布企业负责,一比多公司对此不承担任何保证责任。

友情提醒:为保障您的利益,降低您的风险,建议优先选择商机宝付费会员的产品和服务。


武汉市圣士翻译有限责任公司   地址:武汉汉口中山大道1166号金源世界中心B座22楼   邮政编码:430000
联系人:黎学松   400电话:400-666-2680转2396   电话:027-82780509   手机:13387594863   传真:027-82771087-809
技术支持:一比多  |  免责声明 | 隐私声明
增值电信业务经营许可证:沪B2-20070060     网站Icp备案号:沪ICP备05000175号
<%---站点编号 ----%> <%---页面编号 ----%> <%---页面参数1 ----%> <%---页面参数2----%> <%---页面参数3 ----%>